937 Soldering Station
v
Structure
1.Digital display screen
2.Swith
3.Temperature control button
4.Handle interface
5.Soldering iron stand
6.Cleaning spong
7.Soldering iron tip
8.Soldering iron handle
9.The plug
The soldering station handle
Number of handle holes:Five holes
Soldering iron heater：Four pins
Size：218mm
Lightweight handle handle with lightweight grip, no fatique when used for a long time
Handle base
Material ：Phenolic resin material
Cleaning cotton:Activated carbon cleaning cotton
Size：157*70*77mm
Anti-scaldinq, anti-static, stable socket base
Technical Specifications
Power Consumption: 65W
Input Voltage: 220VAC±10% 50Hz (110VOptional)
Output Voltage: 24V
Temperature Range: 200°c~480°c
Temperature Stability:±5°c
Temperature Accuracy:10°c
Tip to Ground Impedance: <2Ω
Tip to Ground Voltage: <2mV
Setting Mode: Button setting temperature
Temperature-correcting Mode: Analogue Calibration
Heating Core: Four-core Ceramic Heating Core
Physical Dimension of Principal Machine:
140(L)×110(W)×90(H)mm
Standard tip: 900M-T-SI
Weight: Ca. 1.75Kg
Machine table parameters
Model型 号 | 937 |
Power功 率 | 65W |
Display显示屏 | Dial display 数显款 |
Soldering iron heater 发热芯 | Four pins 4针 |
temperature range 温度范围 | 200°c~480°c |
soldering station handle 焊台手柄 | Five holes Soldering iron 手柄五孔 |
The handle length 手柄长度 | 218mm |
Tip model 焊咀型号 | 900M-T-I |
Welding tip/heating core 焊咀/发热芯 | separated type 分体式 |
Size 尺寸 | 140(L)×110(W)×90(H)mm |
Weight 重 量 | 1.75kg |
Features
Increase copper aluminum
Large size transformer, copper-alumin um hybrid, made of silicon steel sheet, faster heat dissipation
SMD motherboard SMD
Double-sided high-quality motherboard, SMD components, effective temperature control.
use switch
If there is a dangerous situation such as leakage or open circuit, the power will be automatically cut off
to prevent the burning of the components and effectively ensure the safety of the product.
Plugable heaing lelment
Plug-in design, easy to replace, PTO material heating elementheats up quickly.
Anti-burning Silicone wire
Silicone wire can effectively prevent urning and scalding, and is safer.
Anti-static soldering iron stand
Phenolic resin material anti-scaldinq, anti-static, stable socket.
Activated carbon cleaning cotton
Effectively remove the oxide of the soldering iron tip and increase the service life of the soldering iron tip.
Anti-slip foot pad
The four-corner rubber feet can effectively fix the bracket and prevent slippage.
Use Guide
1. Operating Instructions
Connect the iron and console
Connect the power
turn on the switch , the power indicator LED that lights up
temperature control button to the suitable temperature location
proper temperature
Start welding
After work, clean the handle and put it back into the bracket
Turn off the power, cool down
When using, try to use low temp for soldering. If the temp exceeds 450 , the oxidation speed of the soldering iron tip is several times that of 370.
The soldering iron should always keep tin on the tip of the soldering iron to prevent oxidation.
Do not apply force or knock when soldering, otherwise the soldering iron tip will be easily damaged and deformed. As lonq as the solderinq iron tip fully contacts the solderinq point, the heat can be fully transferred. In addition, choosinq the right soldering iron tip can effectively help you better Achieve results and improve work efficiency.
2 .non-stick tin tip reasons
tip temperature exceeds 400
to be used in the soldering tip surface did not give proper plus tin.
lack of flux in welding, soldering , repair, welding and other operations .
Wipe the tip on the sulfur content or dry sponge and a rag
exposure to organic materials such as plastic , silicon ( Si ) quality grease and other chemicals
Use impure and low tin content solder
3.Replacement and handling tip
Unscrew sleeve tip can remove replaced. Be sure to turn off the power supply temperature control units and allow the tip to cool down before removing the tip, remove the oxide dust formed in the sleeve fixed premises . Care must be taken to avoid this dust into the eyes. Replace the tip and the normal hand strength to lock the sleeve .
When replacing the new iron core , iron core should be extended stainless steel pipe 23mm, then tighten the mounting screws in the handle iron core.
Note: You must be careful not to over tighten , otherwise it will damage the heating element .
4.General clean up
iron grip or temperature control units with a cloth moistened with a small amount of housing can be liquid detergent to clean .
Do not immerse the fluid temperature control units , or allow liquid to flow into the housing .
Do not use any solvents to clean the shell .
5.The new tip
When any time using the new tip, please follow these steps will make life considerably lengthened tip .
The low temperature setting control knob to the position . Turn the power "switch ."
Heating arrive after 200 , the surface of the tip soldering flux containing tin wire added .
After heating at 200 continued for five minutes , and then transferred to the appropriate temperature setting controls the temperature position.
After reach the appropriate temperature , to get started.
Note: Any time using the new tip every day the best tip can remove foreign objects and clean interior !
6.Proper use of the soldering iron
soldering iron grip : A. Low iron : like holding a pen to write . B. High temperature soldering : finger down grip .
Tip the ideal angle for PCB : 45 .
Tip need to be kept clean .
When using a soldering iron touch the heating element is strictly prohibited .
When using non- violent use of iron ( example: hitting a hard object with tip ) .
7.Maintenance Tip
In order to ensure good function allows normal operation temperature soldering iron , please note the following recommendations. ( If there are certain sets of iron or temperature factors function does not work correctly , please contact the nearest service support services at ) . Tip supplied are all alloy head , if used properly, will have a longer life.
Before the shutdown must be disabled at the tip soldering surface plus the appropriate amount of tin, just before welding smear .
Do not allow the tip long stay in the high temperature , easy to make the tip surface plating layer cracking.
When soldering iron tip should not be too much pressure to the friction pads , this process does not change the thermal performance, but will make the tip damage.
Do not use absolute tip cleanup materials or rough rasp .
If the surface is nonstick tin oxide , can be used as needed carefully rubbing with emery cloth or ethyl alcohol solution to clean up equal , heated to 200 immediately .
Do not use excessive chlorine or acid flux . Use of a synthetic resin or only flux activated resin .
Note : Every 24 hours or at least once a week , remove the tip to clean and remove foreign objects inside the sleeve .
8.Security Code
When the power is turned on , the tip temperature is hot. Given the abuse may cause burns or fires , strictly observe the following:
Do not touch the metal parts near the tip .
Do not use near flammable objects tip .
Notify other personnel workshop , the tip burns easily , may lead to dangerous accidents, should be completed after the break , or turn off the power .
When replacing parts or devices tip , you should turn off the power , and until the tip is cooled to room temperature.
To avoid damage to the welding station and safe working environment , shall comply with the following:
This product uses three-wire grounding plug must be inserted into the three-hole grounded outlet . Do not change the plug or use an ungrounded three
adapters leaving poorly grounded .
For an extension cord , use a grounded three -wire power cord.
Do not use the soldering iron tip to work outside .
Do not knock the table in order to remove residual iron , a move that could seriously damage the earthquake iron .
Do not tamper with welding units .
Do not wet welding sets , or wet hands when using the welding station .
welding will smoke , workshops should be well ventilated.
without any physical injury or damage may be frivolous objects when using the soldering station .
